AUTOVALVE
Take SUPERIOR™ control of your chemical feed system. AutoValve is a microprocessor based device that automatically controls the feed rate of chlorine, sulphur dioxide, or ammonia and is available for automatic residual, flow proportioning, and compound loop control, using process water flow rate, residual setpoint, or a combination of those parameters.
Why SUPERIOR™ AutoValve?
Non Corrosive Materials Of Construction
All Titanium Right Where It Counts
Easy Setup & Calibration
Industry-wide Easiest Operation & BEST PERFORMANCE
Highest Accuracy Powerful Hybrid Stepper Motor
The SUPERIOR™ AutoValve is the only automatic control valve with all three control modes already built in to the controller, so there is no need for additional modules. Quick to set up and simple to use and maintain, just ask any user! Operators and users swear by SUPERIOR™ AutoValve. "It's bulletproof!"
AV-1
SUPERIOR AutoValve
Maximum Capacity 100PPD
2000g/hr
AV-10
SUPERIOR AutoValve
Maximum Capacity 1000PPD
20kg/hr
AV-60
SUPERIOR AutoValve
Maximum Capacity 6000PPD
120kg/hr
AV-2
SUPERIOR AutoValve
Maximum Capacity 250PPD
5kg/hr
AV-20
SUPERIOR AutoValve
Maximum Capacity
2000PPD
20kg/hr
AV-80
SUPERIOR AutoValve
Maximum Capacity 8000PPD
160kg/hr
AV-5
SUPERIOR AutoValve
Maximum Capacity 500PPD
10kg/hr
AV-40
SUPERIOR AutoValve
Maximum Capacity 4000PPD
80kg/hr
AV-100
SUPERIOR AutoValve
Maximum Capacity 10000PPD
200kg/hr
SPECIFICATIONS
STANDARD ACCESSORIES
Stepper Motor:
Bi-polar (4 wire), 5.6 VDC, 1A
Phase Resistance 5.6 Ohms
Phase Inductance 25.6 mH
Holding Torque 72 oz-in
Rotor Inertia 0.00166 oz-in-sec2
​
Valve Plug Travel: 1.25" Maximum
​
Keyboard Inputs:
Dosage Ratio
Alarm set points
Manual position set
Calibration for 0%, 25% & 100%
(Valve Open positions)
4-20 mA input, 4-20 mA output Calibration
Input Signal Filter
(Adjust sensitivity to minor signal change)
​
Control Mode: Manual or Automatic
​
Chemical Feed:
Chlorine Gas, Sulphur Dioxide Gas,
Maximum Anhydrous Ammonia Gas, Sodium Hypochlorite, Aqueous Ammonia, Sodium Bisulfate Solution.
(Consult factory for other liquids.)
​
Maximum Feed Rates:
10, 25, 50, 100, 200 & 500 PPD
(200, 500, 1000, 2000, 5000, 10,000 g/hr)
1,000, 2,000, 4,000, 6,000, 8,000, & 10,000 PPD (20, 40, 80, 120, 160, & 200 kg/hr)
SPECIFICATIONS
STANDARD ACCESSORIES
Power Phase :
115/230 VAC (+ 15%), 50/60 Hz, Single
​
Physical Inputs:
FLOW: 4-20mA DC
VALVE POSITION: Potentiometer input,
(Approx. 0.25-2.25 VDC)
RESIDUAL : 4-20mA DC
​
Display:
2-line, 16 character, back-lighted LCD
​
Calibration:
Factory Set, field adjustable.
0%, 25% & 100% valve setpoints
4mA & 20 mA Input signal
4mA & 20 mA Output (Valve Position)
Input Signal Filter; 0-50S
​​
Alarm Contacts:
10 Amps @120 VAC or 30 VDC
5 Amps @ 240 VAC resistive load, unlatching.
​
Dosage Ratio:
4:1, adjustable through keypad and display.
​
EEPROM:
256 bytes
​
Outputs:
2.5 VDC potentiometer excitation
4-20mA reference to local ground
600 ohm drive (maximum)
​
Dimenions:
24"x24"x6"
​
Shipping Weight:
36 pounds
16.3 kilograms​​​​​​​
SUPERIOR™ Gas Chlorinators are proudly made by Chemical Injection Technologies, Inc.
835 Edwards Road, Fort Pierce, Florida 34982 USA. T: 772-461-0666.